Keyence 1399B Communication Unit User Manual Short Term Confidential

Keyence Corporation Communication Unit Short Term Confidential

(Short-Term Confidential) User Manual

1E HR-100B-IMHandheld Code ReaderHR-100B HR-101B Series Instruction ManualCommunication UnitHR-UC1Desktop holderHR-PU1IntroductionRead this instruction manual before using the product in order to achieve maximum performance. Keep this instruction manual in a safe place after reading it so that it can be used at any time.SymbolsThe following symbols alert you to important messages. Be sure to readthese messages carefully.Important It indicates cautions and limitations that must be followed during operation. PointIt indicates additional information on proper operation. ReferenceIt indicates tips for better understanding or useful information.indicates the reference pages in this manual or the reference pages in separate manuals.Trademarks•Microsoft, Windows, Windows Vista/7/8 and Excel are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.Safety PrecautionsGeneral cautionsPrecautions on LED productsPrecautions on Proper UsePrecautions on regulations and StandardsCE MarkingKeyence Corporation has confirmed that this product complies with the essential requirements of the applicable EC Directive(s), based on the following specifications. Be sure to consider the following specifications when using this product in the Member States of European Union.zR&TTE DirectiveHR-100B, HR-101B and HR-UC1 comply with the requirements of theR&TTE Directive•Declaration of Conformity for each country in accordance with the R&TTE Directive are listed at the end of this document.Precautions on BluetoothImportant•Depending on the environment, communication may be impossible. Before starting actual operation, be sure to test the operation.•If this product is used near devices with the same frequency band, such as a wireless LAN device, microwave oven, heating equipment for industrial use, high-frequency equipment for medical use, etc., radio wave interference may occur and the communication speed will become slow or communication may become impossible.•Communication may be impossible at locations near metallic objects, locations surrounded with metallic walls or where there is a lot of metallic powder.•Possible communication distance is approx. 10 m of vision, however, even within 10 m, communication may become impossible depending on the environment. Check the communication availability before using.•With the frequency band for this unit, premise radio stations (license required), specified low power radio stations (license not required) and amateur radio stations (license required) for identifying mobile objects are operating. Those mobile objects are used for industrial, scientific and medical equipment, and also used for factory production lines.1. Before using this unit, be sure to check that premise radio stations, specified low power radio stations and amateur radio stations for identifying mobile objects are not operating in the vicinity.2. If radio wave interference occurs from the this unit against premise radio stations for identifying mobile objects, change the usable frequency immediately or stop the electric wave generation, and then contact the below phone number in regard to taking necessary measures (e.g. setting a partition) to avoid interference. DANGERIt indicates a hazardous situation which, if not avoided, will result in death or serious injury.WARNINGIt indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTIONIt indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICEIt indicates a situation which, if not avoided, could result in product damage as well as property damage. DANGER•This product is only intended to detect object(s). Do not use this product for the purpose to protect a human body or a part of human body.•This product is not intended for use as an explosion-proof product. Do not use this product in a hazardous location and/or potentially explosive atmosphere.CAUTION•At startup and during operation, be sure to monitor the functions and performance of this product and confirm normal operation.•Take substantial safety measures to avoid any damage in the event that this product malfunctions.•Using this product in applications other than specified in this manual is prohibited. Fire, electric shock or product failure may occur.NOTICE•KEYENCE cannot guarantee the functionality or performance of units that have been modified or used with specifications other than those described in this manual.•When the KEYENCE products are used in combination with other devices, functions and performance may be degraded, depending on the operating conditions and surrounding environment.96M13817CAUTIONControls or adjustments other than those specified in this manual may result in a hazardous amount of LED exposure. Make sure to observe the following instructions. Otherwise, injury to the human body (eyes, skin, etc.) may result.•Do not directly stare into the laser beams or specularly reflected light.•This product is not equipped with a mechanism to stop laser emission when disassembled. Never disassemble this product.•Do not directly stare into the laser beams using an optical apparatus. If you observe the laser beams with certain types of optical apparatus (e.g. loupe, magnifying glass, microscope) within the distance of 100 mm, injury to eyes may result.CAUTION•When using the HR-UC1/PU1, make sure to use the optional AC adaptor (OP-87530/88046). Using AC adaptors other than these may result in fire, electric shock, or product failures.NOTICE•Do not disassemble or modify the HR-100B Series. Doing so may damage the unit.•The HR-100B Series is a precision instrument. Dropping this product or subjecting it to shock may cause damage. Be careful when carrying or using this unit.•Do not allow water, oil, dust, or other foreign substances to stick to the scanner of the HR-100B Series. This may cause read errors. Use a soft, dry cloth to wipe any substance from the scanner. (Do not use a cloth dipped in alcohol or other cleaning substance.)•Place cables as far away as possible from high-voltage lines and power lines.Otherwise, generated noise may cause product failure or operation errors.•Do not hold the HR-100B Series by its cable. The main unit may strike the wall and may be damaged. Also due to the stress on the cables, the wires may break.•Be sure to periodically clean the power connection part of AC adaptor connected to the OP-87530/88046 as it tends to catch dust. Tracking phenomenon may result in fire. Also, disconnect the AC adaptor from the outlet if not using for a long period of time.•Use AC power cords that fit shapes of plugs used in each country and/ or region. Also, check if such cords comply with the relevant regulations and standards in each country and/ or region.WARNINGRemove the main battery of HR-100B Series near locations where using wireless devices is banned at medical institutions or near electric devices for medical purposes. Carry and use the product away from an implanted cardiac pacemaker.
2E HR-100B-IM[Japan]•Never disassemble or modify this unit as this conduct is prohibited by the Radio Act. This unit is specified radio equipment based on Japan's Radio Act, and has obtained a certification of construction type according to the standard specified by the Radio Act.[China][Thai]This telecommunication equipment conforms to NTC technical requirement.FCC RegulationsHR-100B, HR-101B and HR-UC1 comply with the following regulations specified by the FCC.•Applicable regulationFCC Part 15 Subpart B ClassBFCC Part 15 Subpart C•This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation.IC (Industry Canada) RegulationsThe HR-100B, HR-101B and HR-UC1 comply with the following regulations specified by the IC.•Applicable regulationICES-003Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Explanation of symbolsChecking the PackageOptionsCommunication cableCommunication unitHR-UC1Desktop holderHR-PU1Battery packHR-B1AC adapterCAUTION•When using the HR-UC1, be sure to attach the ferrite core the nearest position of HR-UC1 to the communication cable and AC adapter.* Please use the following product for the ferrite core.Ferrite core(Manufacturer) : ZCAT3035-1330(TDK)The number of times of the turn : 2 turns•When using the HR-UC1, be sure to provide Class D ground for installation location.DC MarkWEEEThis symbol indicates a direct current.This symbol indicates a separate collection for WEEE.AC adapter polarity markMark for opening and closing the lid.This symbol indicates the polarity of the power plug. This symbol indicates the rotation direction to open or close the battery lid.  Ŷ使用频率：*+]Ŷ等效全向辐射功率(,53：天线增益＜G%L时：P:或G%PŶ最大功率谱密度：天线增益＜G%L时：G%P0+](,53Ŷ载频容限：SSPŶ杂散发射辐射功率对应载波倍信道带宽以外：G%PN+]0+]G%PN+]*+]G%P0+]*+]G%P0+]*+]G%P0+]其它*+]不得擅自更改发射频率、加大发射功率包括额外加装射频功率放大器，不得擅自外接天线或改用其它发射天线；使用时不得对各种合法的无线电通信业务产生有害干扰；一旦发现有干扰现象时，应立即停止使用，并采取措施消除干扰后方可继续使用；使用微功率无线电设备，必须忍受各种无线电业务的干扰或工业、科学及医疗应用设备的辐射干扰；不得在飞机和机场附近使用。Main unit (HR-100B or HR-101B) . . .1Instruction manual . . .1HR-1C3UNUSB 3 m straightHR-1C3UCUSB 3 m curl typeHR-1C5UCUSB 5 m curl typeHR-1C3RBRS-232C type for HR-UC1OP-87530OP-880461E HR-100B-IMHandheld Code ReaderHR-100B HR-101B Series Instruction ManualCommunication UnitHR-UC1Desktop holderHR-PU1Read this instruction manual carefully prior to operating the HR-100B Series Handheld Code Reader.Keep this manual in a safe place for future reference.IntroductionRead this instruction manual before using the product in order to achieve maximum performance. Keep this instruction manual in a safe place after reading it so that it can be used at any time.SymbolsThe following symbols alert you to important messages. Be sure to readthese messages carefully.Important It indicates cautions and limitations that must be followed during operation. PointIt indicates additional information on proper operation. ReferenceIt indicates tips for better understanding or useful information.indicates the reference pages in this manual or the reference pages in separate manuals.TrademarksMicrosoft, Windows, Windows Vista and Excel are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.Safety PrecautionsGeneral cautionsPrecautions on LED productsPrecautions on Proper UsePrecautions on regulations and StandardsCE MarkingKeyence Corporation has confirmed that this product complies with the essential requirements of the applicable EC Directive(s), based on the following specifications. Be sure to consider the following specifications when using this product in the Member States of European Union.zR&TTE DirectiveHR-100B, HR-101B and HR-UC1 comply with the requirements of theR&TTE DirectiveDeclaration of Conformity for each country in accordance with the R&TTE Directive are listed at the end of this document.Precautions on BluetoothImportantDepending on the environment, communication may be impossible. Before starting actual operation, be sure to test the operation.If this product is used near devices with the same frequency band, such as a wireless LAN device, microwave oven, heating equipment for industrial use, high-frequency equipment for medical use, etc., radio wave interference may occur and the communication speed will become slow or communication may become impossible.Communication may be impossible at locations near metallic objects, locations surrounded with metallic walls or where there is a lot of metallic powder.Possible communication distance is approx. 10 m of vision, however, even within 10 m, communication may become impossible depending on the environment. Check the communication availability before using.With the frequency band for this unit, premise radio stations (license required), specified low power radio stations (license not required) and amateur radio stations (license required) for identifying mobile objects are operating. Those mobile objects are used for industrial, scientific and medical equipment, and also used for factory production lines.1. Before using this unit, be sure to check that premise radio stations, specified low power radio stations and amateur radio stations for identifying mobile objects are not operating in the vicinity.2. If radio wave interference occurs from the this unit against premise radio stations for identifying mobile objects, change the usable frequency immediately or stop the electric wave generation, and then contact the below phone number in regard to taking necessary measures (e.g. setting a partition) to avoid interference. DANGERIt indicates a hazardous situation which, if not avoided, will result in death or serious injury.WARNINGIt indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTIONIt indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICEIt indicates a situation which, if not avoided, could result in product damage as well as property damage. DANGERThis product is only intended to detect object(s). Do not use this product for the purpose to protect a human body or a part of human body.This product is not intended for use as an explosion-proo f product. Do not use this product in a hazardous location and/or potentially explosive atmosphere.CAUTIONAt startup and during operation, be sure to monitor the functions and performance of this product and confirm normal operation.Take substantial safety measures to avoid any damage in the event that this product malfunctions.Using this product in applications other than specified in this manual is prohibited. Fire, electric shock or product failure may occur.NOTICEKEYENCE cannot guarantee the functional ity or performance of un its that have been modified or used with specifications other than those described in this manual.When the KEYENCE products are used in combination with other devices, functions and performance may be degraded, depending on the operating conditions and surrounding environment.96M13817CAUTIONControls or adjustments other than those specified in this manual may result in a hazardous amount of LED exposure. Make sure to observe the following instructions. Otherwise, injury to the human body (eyes, skin, etc.) may result.Do not directly stare into the laser beams or specularly reflected light.This product is not equipped with a mechanism to stop laser emission when disassembled. Never disassemble this product.Do not directly stare into the laser beams using an optical apparatus. If you observe the laser beams with certain types of optical apparatus (e.g. loupe, magnifying glass, microscope) within the distance of 100 mm, injury to eyes may result.NOTICEDo not disassemble or modify the HR-100B Series. Doing so may damage the unit.The HR-100B Series is a precision instrument. Dropping this product or subjecting it to shock may cause damage. Be careful when carrying or using this unit.Do not allow water, oil, dust, or other foreign substances to stick to the scanner of the HR-100B Series. This may cause read errors. Use a soft, dry cloth to wipe any substance from the scanner. (Do not use a cloth dipped in alcohol or other cleaning substance.)Place cables as far away as possible from high-voltage lines and power lines.Otherwise, generated noise may cause product failure or operation errors.Do not hold the HR-100B Series by its cable. The main unit may strike the wall and may be damaged. Also due to the stress on the cables, the wires may break.Be sure to periodically clean the power connection part of AC adaptor connected to the OP-87530/88046 as it tends to catch dust. Tracking phenomenon may result in fire. Also, disconnect the AC adaptor from the outlet if not using for a long period of time.Use AC power cords that fit shapes of plugs used in each country and/ or region. Also, check if such cords comply with the relevant regulations and standards in each country and/ or region.CAUTIONWhen using the HR-UC1/PU1, make sure to use the optional AC adaptor (OP-87530/88046). Using AC adaptors other than these may result in fire, electric shock, or product failures.WARNINGRemove the main battery of HR-100B Series near locations where using wireless devices is banned at medical institutions or near electric devices for medical purposes. Carry and use the product away from an implanted cardiac pacemaker.
3E HR-100B-IMPart Names and FunctionsOperation status LEDThe operation status LED lights up as below according to the operation status.Basic OperationsBring the reading window to the code and press the trigger switch. The LED light and the aimer indicating the reading position are emitted, and the code is read.•When the code is read, the operation status LED (green) lights up and the buzzer sounds.(The operation status LED and the buzzer can be disabled.)•The read code data is sent to the connected PC or other equipment.Removing the battery cover1Rotate the screw counterclockwise to loosen it.2Push the cover up and at an angle with your thumb to remove it.Inserting the battery and securing the cover1Insert the battery straight in as shown in the figure below.2Attach the cover to the hook and close it.Rotate the screw clockwise to secure the cover.3Return the metal loop used to rotate the screw to the flat position.LED color LED light-up timingGreen •When a code is read•When a setting code is read in the setting modeRed •When an operation error occurs when an operation is specified•When an invalid setting code is read while reading a setting codeTrigger switch:Use this switch to read a code.Operation status LED:indicates the operation status.Reading window:Emits LED light and aimer and receives the reflected light.BuzzerHook
4E HR-100B-IM[Communication unit] Connecting the communication cable1Insert the connector straight in with the tab facing outward.[Communication unit/Desktop holder] Connecting the power cable1Insert the AC cable into the AC adapter.2Insert the connector of the AC adapter as shown in the figure below.Pairing1Read the barcode on the back of the communication unit.After a series of short beeps, a tone sounds if pairing is successful.Ŷ FCC RegulationsHR-100B, HR-101B and HR-UC1 comply with the followingregulations specified by the FCC.• Applicable regulationFCC Part 15 Subpart B ClassBFCC Part 15 Subpart C• This device complies with part 15 of the FCC Rules. Operationis subject to the following two conditions: (1)This device maynot cause harmful interface, and (2) this device must acceptany interference received, including interference that maycause undesired operation.Note: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or moreof the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.・This equipment complies with FCC radiation exposure limitsset forth for an controlled environment and meets the FCC radiofrequency (RF) Exposure Guidelines. This equipment has verylow levels of RF energy that is deemed to comply without testingof specific absorption rate(SAR).• When using the HR-UC1, be sure to attach the ferritecore the nearest position of HR-UC1 to thecommunication cable and AC adapter.* Please use the following product for the ferrite core.Ferrite core(Manufacturer) : ZCAT3035-1330(TDK)The number of times of the turn : 2 turns• When using the HR-UC1, be sure to provide Class Dground for installationlocation.・FCC CAUTION Changes or modifications not expressly approved by theparty responsible for compliance could void the user’sauthority to operate the equipment.Ŷ IC (Industry Canada) RegulationsThe HR-100B, HR-101B and HR-UC1 comply with the followingregulations specified by the IC.• This device complies with Industry Canada’s licence-exempt RSSs.• Applicable regulationICES-003Operation is subject to the following two conditions: (1) this devicemay not cause interference, and (2) this device must accept anyinterference, including interference that may cause undesiredoperation of the device.• Le présent appareil est conforme aux CNR d'Industrie Canadaapplicables aux appareils radio exempts de licence.L'exploitation estautorisée aux deux conditions suivantes : (1) l'appareil ne doit pasproduire de brouillage, et (2) l'utilisateur de l'appareil doit acceptertout brouillage radioélectrique subi, même si le brouillage estsusceptible d'en compromettre le fonctionnement.• This equipment complies with IC radiation exposure limits set forthfor an uncontrolled environment and meets RSS-102 of the IC radiofrequency (RF) Exposure rules. This equipment has very low levels ofRF energy that are deemed to comply without testing of specificabsorption rate (SAR).• Cet équipement est conforme aux limites d’exposition auxrayonnements énoncées pour un environnement non contrôlé etrespecte les règles d’exposition aux fréquences radioélectriques (RF)CNR-102 de l’IC. Cet équipement émet une énergie RF très faible quiest considérée comme conforme sans évaluation du débitd’absorption spécifique (DAS).
5E HR-100B-IMGeneral specificationsHandheld Code ReaderCommunication unit/Desktop holderModel HR-100B HR-101BType Standard type High resolution typeLight-receiving part Sensor CMOS image sensorNumber of pixels 838×640 pixelsLight-emitting part(light and aimer)Light source Red LEDLED class Exempt group (IEC62471)Reading specificationsSupported symbol2D CodeQR, MicroQR, DataMatrix (ECC200)PDF417, MicroPDF417, GS1 Composite (CC-A/CC-B/CC-C), MaxiCode, AztecCodeBarcodeCODE39, ITF, 2of5 (Industrial 2of5), NW-7 (Codabar), CODE128, GS1-128, GS1 DataBar, CODE93, JAN/EAN/UPC, MSI, Postal, CODE11, 2of5Minimum resolution 2D code 0.169 mm 0.127 mmBarcode 0.127 mm 0.076 mmReading distance(Typical examples)2D code 15 mm to 180 mm(Cell size: 0.254 mm)0 mm to 114 mm(Cell size: 0.254 mm)Barcode 25 mm to 115 mm(Narrow bar width: 0.127 mm)0 mm to 96 mm(Narrow bar width: 0.127 mm)Focal distance 100 mm 50 mmField of view in focal distance 106 mm × 80 mm 64 mm × 49 mmWirelessStandard Bluetooth Ver 2.1Frequency 2.4 GHz bandwidthBroadcast output Class 2Communication distance Approx. 10 m with few obstructionsBaud rate Max 1 MbpsEnvironmental resistanceAmbient temperature 0°C to 50°CAmbient storage temperature -40°C to 70°CAmbient humidity 5 to 95% (No condensation)Storage ambient humidity 5 to 95% (No condensation)Ambient luminance Sunlight: 10,000 lx, fluorescent lamp: 2,000 lxDrop impact resistance Concrete 1.8 m, 50 timesOperating environment No dust or corrosive gas presentEnclosure rating IP41BatteryModel HR-B1Continuous usage time (typical value:1scan/s) 14 hoursCharging time Approx. 4.5 hours with AC adapterApprox. 9 hours through USB bus powerDimension 161 mm × 86 mm (Head) × 71 mm (Head)Weight Approx. 225 gModel HR-UC1 HR-PU1Type Communication unit Desktop holderWirelessStandard Bluetooth Ver 2.1―Frequency 2.4 GHz bandwidth―Broadcast output Class 2―Communication distance Approx. 10 m with few obstructions―Baud rate Max 1 Mbps―CommunicationUSB Standard USB Ver 1.1 (USB-HID, USB-COM)―Supported OS Windows 8, 7, Vista, XP―RS-232CSynchronization method Asynchronous―Transmission code ASCII code―Baud rate 300, 600, 1200, 2400, 4800, 9600,19200, 38400, 57600, 115200 bps―Data length 7/8 bit―Parity check None/Odd/Even―Stop bit length 1/2 bit―Charging time Approx. 4.5 hours with AC adapterApprox. 9 hours through USB connection (HR-UC1 only)Environmental resistanceAmbient temperature(When not charging) 0°C to 50°CAmbient temperature(When charging) 5°C to 40°CAmbient storage temperature -40°C to 70°CAmbient humidity 5 to 95% (No condensation)Storage ambient humidity 5 to 95% (No condensation)Drop impact resistance Concrete 1 m, 50 timesOperating environment No dust or corrosive gas presentEnclosure rating IP41RatingPower supply voltage DC 4.5 V to 5.5 VCurrent consumption (USB) 500 mA―Current consumption (AC adapter) 1000 mADimension 81 mm × 132 mm × 101 mmWeight Approx. 180 g
6E HR-100B-IMBattery packCommunication cableAC adapterModel HR-B1Type Lithium ion rechargeable batteryNominal output voltage 3.75 VNominal capacity 2400 mAhEnvironmentalresistanceAmbient storage temperature -20°C to 60°CStorage ambient humidity 45 to 85% (No condensation)Dimension 21 mm x 22 mm x 100 mmWeight Approx. 65 gModel HR-1C3UN HR-1C3UC HR-1C5UC HR-1C3RBCable type Straight CurlCable length Approx. 3 m Approx. 5 m Approx. 3 mInterface USB RS-232CConnector USB (A type) D-sub 9 pin (female)Weight Approx. 130 g Approx. 130 g Approx. 200 g Approx. 160 gModel OP-87530 OP-88046RatingInput AC100 to 240 V 50/60 Hz 0.27 to 0.17 AOutput DC5 V Max. 2 A DC5 V Max. 2.5 AAmbient temperature 0°C to 40°CAmbient storage temperature -20°C to 60°C -10°C to 70°CDimension 72 mm × 47 mm × 27 mm (excluding cables) 81 mm × 50 mm × 31 mm (excluding cables)Weight Approx. 140 g Approx. 175 g
7E HR-100B-IMDimensional Outline DrawingsHR-100B/101B(Unit: mm)HR-1C3UN(Unit: mm)HR-1C3UC(Unit: mm)HR-1C5UC(Unit: mm)HR-1C3RB(Unit: mm)HR-UC1/PU1(Unit: mm)HR-B1(Unit: mm)OP-87530(Unit: mm)OP-88046(Unit: mm)86307116143φ5(45) (33)(16)2980±20(φ19)205±25(RETRACTED) 1650±150(EXTENDED)φ5(45)(33)(16)250±20(φ19)910±20540±40(RETRACTED) 4300±150(EXTENDED)φ5(45)(33)(16)250±20(φ19)250±201650±150(EXTENDED)250±25(RETRACTED)(45)AA250±20910±20(φ19)(34)(34)(30) (15)(45) 220φ5101 811322221100(47)(27) (72) (28)(26)1800φ3.5(φ8)813150
8E HR-100B-IMDeclaration of Conformity for Each Country inAccordance with the R&TTE DirectiveWARRANTIES AND DISCLAIMERS(1) KEYENCE warrants the Products to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment. If any models or samples were shown to Buyer, such models or samples were used merely to illustrate the general type and quality of the Products and not to represent that the Products would necessarily conform to said models or samples. Any Products found to be defective must be shipped to KEYENCE with all shipping costs paid by Buyer or offered to KEYENCE for inspection and examination. Upon examination by KEYENCE, KEYENCE, at its sole option, will refund the purchase price of, or repair or replace at no charge any Products found to be defective. This warranty does not apply to any defects resulting from any action of Buyer, including but not limited to improper installation, improper interfacing, improper repair, unauthorized modification, misapplication and mishandling, such as exposure to excessive current, heat, coldness, moisture, vibration or outdoors air. Components which wear are not warranted.(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They are only suggestions, and it is Buyer's responsibility to ascertain the fitness of the Products for Buyer’s intended use. KEYENCE will not be responsible for any damages that may result from the use of the Products.(3) The Products and any samples ("Products/Samples") supplied to Buyer are not to be used internally in humans, for human transportation, as safety devices or fail-safe systems, unless their written specifications state otherwise. Should any Products/Samples be used in such a manner or misused in any way, KEYENCE assumes no responsibility, and additionally Buyer will indemnify KEYENCE and hold KEYENCE harmless from any liability or damage whatsoever arising out of any misuse of the Products/Samples.(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED.IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE LIABLE TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING FROM LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF INFORMATION, LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES WAS ADVISED OF A POSSIBLE THIRD PARTY’S CLAIM FOR DAMAGES OR ANY OTHER CLAIM AGAINST BUYER. In some jurisdictions, some of the foregoing warranty disclaimers or damage limitations may not apply.BUYER'S TRANSFER OBLIGATIONS:If the Products/Samples purchased by Buyer are to be resold or delivered to a third party, Buyer must provide such third party with a copy of this document, all specifications, manuals, catalogs, leaflets and written information provided to Buyer pertaining to the Products/Samples.E 1101-3ýesky[Czech]KEYENCE CORPORATION tímto prohlašuje, že tento HR-100B/HR-101B/HR-UC1 je ve shodČ se základními požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES.Dansk[Danish]Undertegnede KEYENCE CORPORATION erklærer herved, at følgende udstyr HR-100B/HR-101B/HR-UC1 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Deutsch[German]Hiermit erklärt KEYENCE CORPORATION, dass sich das Gerät HR-100B/HR-101B/HR-UC1 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Eesti[Estonian]Käesolevaga kinnitab KEYENCE CORPORATION seadme HR-100B/HR-101B/HR-UC1 vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.EnglishHereby, KEYENCE CORPORATION, declares that this HR-100B/HR-101B/HR-UC1 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Español[Spanish]Por medio de la presente KEYENCE CORPORATION declara que el HR-100B/HR-101B/HR-UC1 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.ǼȜȜȘȞȚțȒ[Greek]ȂǼ ȉǾȃ ȆǹȇȅȊȈǹ KEYENCE CORPORATION ǻǾȁȍȃǼǿ ȅȉǿ HR-100B/HR-101B/HR-UC1 ȈȊȂȂȅȇĭȍȃǼȉǹǿ ȆȇȅȈ ȉǿȈ ȅȊȈǿȍǻǼǿȈ ǹȆǹǿȉǾȈǼǿȈ Ȁǹǿ ȉǿȈ ȁȅǿȆǼȈ ȈȋǼȉǿȀǼȈ ǻǿǹȉǹȄǼǿȈ ȉǾȈ ȅǻǾīǿǹȈ 1999/5/ǼȀ.Français[French]Par la présente KEYENCE CORPORATION déclare que l'appareil HR-100B/HR-101B/HR-UC1 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Italiano[Italian]Con la presente KEYENCE CORPORATION dichiara che questo HR-100B/HR-101B/HR-UC1 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Latviski[Latvian]Ar šo KEYENCE CORPORATION deklarƝ, ka HR-100B/HR-101B/HR-UC1 atbilst DirektƯvas 1999/5/EK bnjtiskajƗm prasƯbƗm un citiem ar to saistƯtajiem noteikumiem.Lietuviǐ[Lithuanian]Šiuo KEYENCE CORPORATION deklaruoja, kad šis HR-100B/HR-101B/HR-UC1 atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Nederlands[Dutch]Hierbij verklaart KEYENCE CORPORATION dat het toestel HR-100B/HR-101B/HR-UC1 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Malti[Maltese]Hawnhekk, KEYENCE CORPORATION, jiddikjara li dan HR-100B/HR-101B/HR-UC1 jikkonforma mal-ƫtiƥijiet essenzjali u ma provvedimenti oƫrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.Magyar[Hungarian]Alulírott, KEYENCE CORPORATION nyilatkozom, hogy a HR-100B/HR-101B/HR-UC1 megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Português[Portuguese]KEYENCE CORPORATION declara que este HR-100B/HR-101B/HR-UC1 está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko[Slovenian]KEYENCE CORPORATION izjavlja, da je ta HR-100B/HR-101B/HR-UC1 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloþili direktive 1999/5/ES.Slovensky[Slovak]KEYENCE CORPORATION týmto vyhlasuje, že HR-100B/HR-101B/HR-UC1 spĎĖa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi[Finnish]KEYENCE CORPORATION vakuuttaa täten että HR-100B/HR-101B/HR-UC1 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Svenska[Swedish]Härmed intygar KEYENCE CORPORATION att denna HR-100B/HR-101B/HR-UC1 står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.Íslenska[Icelandic]Hér með lýsir KEYENCE CORPORATION yfir því að HR-100B/HR-101B/HR-UC1 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.Norsk[Norwegian]KEYENCE CORPORATION erklærer herved at utstyret HR-100B/HR-101B/HR-UC1 er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.cs dadeeteneselfritlvltnlmthuptslskfisvisnoCopyright (c) 2015 KEYENCE CORPORATION. All rights reserved.13817E 1115-1 96M13817 Printed in Japan

Navigation menu