Penclic K2 PENCLIC WIRELESS KEYBOARD User Manual MIN K wireless PRINTx

Penclic AB PENCLIC WIRELESS KEYBOARD MIN K wireless PRINTx

USERS MANUAL

www.penclic.se 1 2
Penclic wireless Keyboard Quick guide EN Quick guide 2 Smile.
EN Penclic wireless Keyboard setup Fn + Function F2 Mute F3 Lower volume F4 Higher volume F9 Pause/Break F10 Scroll Lock F11 Num Lock F12 Print Screen Delete Insert Up arrow Page Up Left arrow Home Down Arrow Page Down Right Arrow End LED behavior Indication 1 red flash The keyboard on/ off switch was set to on. LED flashes red repeatedly Recharge your battery. (NOTE:Do not recharge non-rechargeable batteries.) LED flashes green repeatedlyBattery is currently being recharged. LED is constantly greenBattery is currently being recharged. 2 Welcome to the quick guide. Penclic wireless Keyboard combines ergonomically sound design with modern keyboard technology to bring you comfort and efficiency. Insert the rechargeable batteries and start charging with the included USB charging cable, the USB port supports only charging function. then set the keyboard power switch on the bottom of the keyboard to ON. Driver installation starts automatically. The wireless connection activates automatically. How to use your Penclic wirelessss Keyboard Penclic wireless Keyboard K2 (wireless) has 1 LED indicating battery status. Num Lock actives the numpad functions which is the smaller orange numbers. Special functions (blue text) activated by holding the Fn key and then pressing: 3
Technical specifications · · · The supported platforms for Penclic wireless Keyboard are all operating systems that support HID 1.1. These include Windows XP or later, Mac OSX version 10.1 or later and most Linux/BSD flavors. No extra software/driver installation is needed. Connection USB. AAA 1.2V NiMH Recharging battery (Everyday use last approximately 2 months before charging is needed). -Charging via USB . Troubleshooting · Make sure the Penclic wireless Keyboard USB connector is firmly attached to the computer’s USB port. · Un-plug and re-plug the USB receiver. · Connect to another USB port. · LR 03/AAA/1.5V Alkaline None rechargeable battery can be used. NOTE: DO NOT RECHARGE. · · Connect to another computer. Check the battery. · USB-receiver 2,4GHz. -Wireless reach, minimum 5 metres -Connection via USB . Technical support · Energy saving mode starts after 10 min, press a button to start. · MAC operating systems do not support all the special functions. Measurements · Height: 6 mm (21 mm at top), Base: 285 x 162 mm. · Weight: 381g including 1.4m cable. Should you require additional technical support with your Penclic®, please use our Web site (www.penclic.se) for further information or contact our support group through e-mail. Call Technical Support during business hours, Central European time (UTC+1). Contact + 46 8 544 98 995 contact@penclic.se 5
6
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu