Pilz and KG PITM2 RFID Operating mode selector User Manual Manual

Pilz GmbH & Co. KG RFID Operating mode selector Manual

Manual

PITm2.1pDMGOperatingManual1003182EN02Operatorterminals
PrefaceThisdocumentistheoriginaldocument.AllrightstothisdocumentationarereservedbyPilzGmbH&Co.KG.Copiesmaybemadeforinternalpurposes.Suggestionsandcommentsforimprovingthisdocumentationwillbegratefullyreceived.Pilz®,PIT®,PMI®,PNOZ®,Primo®,PSEN®,PSS®,PVIS®,SafetyBUSp®,SafetyEYE®,SafetyNETp®,thespiritofsafety®areregisteredandprotectedtrademarksofPilzGmbH&Co.KGinsomecountries.SDmeansSecureDigital
ContentOperatingManualPITm2.1pDMG1003182EN02 3Section1 Introduction 51.1 Validityofdocumentation 51.1.1 Retainingthedocumentation 51.2 Definitionofsymbols 6Section2 Overview 72.1 Featuresoftheoperatingmodeselectorswitch 82.2 Featuresofthetransponderkey 9Section3 Safety 103.1 Intendeduse 103.2 Safetyregulations 113.2.1 Useofqualifiedpersonnel 113.2.2 Warrantyandliability 113.2.3 Disposal 11Section4 Functiondescription 124.1 Interfaceforstatusinformation 144.1.1 Timingdiagramsforoperatoractions 164.1.2 Timingdiagramfordeviceerror 174.1.3 Timingdiagramsforusererror:"Noauthorisation" 184.1.4 Timingdiagramsforusererror:"Buttonoperatedincorrectly" 204.2 Operatingmodeinterface 224.2.1 Switchbehaviourafteratransponderkeyisremoved 224.2.2 Controlprogramrequirements 234.3 KeyIDinterface 244.3.1 KeyIDnumberofthetransponderkey 244.3.2 CommunicationmodefordownloadingtheKeyIDnumber 264.3.2.1 Transmittercontrolledcommunicationmode 264.3.2.2 Handshakecontrolledcommunicationmode 274.3.3 Evaluationbyacontrolsystem 284.3.3.1 EvaluationoftheKeyIDnumberwithtransmittercontrolledcommunication284.3.3.2 EvaluationoftheKeyIDnumberwithhandshakecontrolledcommunication31Section5 Installation 355.1 Generalinstallationguidelines 355.2 Dimensions 36Section6 Wiring 376.1 Terminalconfiguration 376.2 Connectingtheunit 386.3 Connectiontoacontrolsystem 39Section7 Operation 427.1 SelectoperatingmodesOM1...OM4 437.2 SelectspecialmodeOM5(Service) 44
ContentOperatingManualPITm2.1pDMG1003182EN02 47.3 Monitoringofoperatingtime 457.4 Switchoverdelayt1 457.5 Troubleshooting 467.6 Diagnostics 477.6.1 Statusinformationabouttheinterfaceforstatusinformation 477.6.2 Statusinformationaboutpushbuttonbacklighting 47Section8 Technicaldetails 488.1 Safetycharacteristicdata 50Section9 Supplementarydata 519.1 Radioapproval 51Section10 Orderreference 5210.1 Product 5210.2 Accessories 52
IntroductionOperatingManualPITm2.1pDMG1003182EN02 51 Introduction1.1 ValidityofdocumentationThisdocumentationisvalidfortheproductPITm2.1pDMG.Itisvaliduntilnewdocumentationispublished.Thisoperatingmanualexplainsthefunctionandoperation,describestheinstallationandprovidesguidelinesonhowtoconnecttheproduct.1.1.1 RetainingthedocumentationThisdocumentationisintendedforinstructionandshouldberetainedforfuturereference.
IntroductionOperatingManualPITm2.1pDMG1003182EN02 61.2 DefinitionofsymbolsInformationthatisparticularlyimportantisidentifiedasfollows:DANGER!Thiswarningmustbeheeded!Itwarnsofahazardoussituationthatposesanimmediatethreatofseriousinjuryanddeathandindicatespreventivemeasuresthatcanbetaken.WARNING!Thiswarningmustbeheeded!Itwarnsofahazardoussituationthatcouldleadtoseriousinjuryanddeathandindicatespreventivemeasuresthatcanbetaken.CAUTION!Thisreferstoahazardthatcanleadtoalessseriousorminorinjuryplusmaterialdamage,andalsoprovidesinformationonpreventivemeasuresthatcanbetaken.NOTICEThisdescribesasituationinwhichtheproductordevicescouldbedamagedandalsoprovidesinformationonpreventivemeasuresthatcanbetaken.Italsohighlightsareaswithinthetextthatareofparticularimportance.INFORMATIONThisgivesadviceonapplicationsandprovidesinformationonspecialfeatures.
OverviewOperatingManualPITm2.1pDMG1003182EN02 72 OverviewTheoperatingmodeselectorswitchmayonlybeoperatedinconjunctionwiththetransponderkeySmartkey®.6transponderkeysareavailable,eachwithdifferentauthorisations.Transponder key24 V DCEvaluation deviceSafety control system (e.g. PNOZ m1p) with "1oon" evaluationHigher-levelprocess control systemIDo0 ... IDo3,IDi0, IDi1SIo0 ... SIo3SOM1SOM2SOM3SOM4SOM5ServiceIn nIn n+1In n+2In n+3In n+4A1A2Antenna +Antenna -n.c.Antenna6 464Fig.:Operatingmodeselectorswitchinanapplication(principle)
OverviewOperatingManualPITm2.1pDMG1003182EN02 82.1 FeaturesoftheoperatingmodeselectorswitchTheproducthasthefollowingfeatures:}Supplyvoltage24VDC}4pushbuttonsforswitchingtheoperatingmode}Selectedoperatingmodeisdisplayedthroughpushbuttonbacklighting}4operatingmodesOM1...OM4}1specialmodeOM5(Service)}1masterauthorisation}5monitoredsemiconductoroutputs(24V)inaccordancewithEN614961;1semiconductoroutputperoperatingmode}Interfaceforstatusinformation,consistingof4signaloutputs(24V)}Statusinformationisdividedintoinformationclasses:– OperatoractionsSelecttransponderkeyRemovetransponderkeySelectoperatingmode– Messages(e.g.usererror,fault)}Interface(KeyIDinterface)fordownloadingtheKeyIDnumberofthetransponderkeyyouareusing,consistingof– 4semiconductoroutputs(24V)– 2inputs}ConfigurablecommunicationmodefordownloadingtheKeyIDnumber– Transmittercontrolledcommunicationmode– Handshakecontrolledcommunicationmode
OverviewOperatingManualPITm2.1pDMG1003182EN02 92.2 FeaturesofthetransponderkeyAtransponderkeycontainsaKeyIDnumberandtheauthorisationstowhichyoucanswitchwiththattransponderkey.Features:}Replacesthemechanicalkey}Differentauthorisations}Authorisationsareidentifiedviaprinted"KeyMode".
SafetyOperatingManualPITm2.1pDMG1003182EN02 103 Safety3.1 IntendeduseTheoperatingmodeselectorswitchissuitableformachinesthatcanbeoperatedinmultipleoperatingmodeswithdifferentprotectivemeasuresand/orworkprocedures.Itenablesyoutoswitchbetweendefinedoperatingmodes,suchas:}Setupmode}Manualmode}Automaticmode}ServiceTheoperatingmodeselectorswitchmeetsthefollowingsafetyrequirements:}InterlocktoprotectagainstunauthorisedswitchingContactwithatransponderkeyisrequiredinordertoswitchtoanoperatingmode.}AccessauthorisationsarerestrictedtocertaingroupsAtransponderkeywiththerelevantauthorisationisrequiredinordertoswitchtoacertainoperatingmode.}PreventsunintentionalswitchingTheswitchtoadifferentoperatingmodeisonlyrecognisedoncethecorresponding(selection)pushbuttonhasbeenoperatedforadefinedperiod("deliberateoperatoraction").Multipleoperationof(selection)pushbuttonsisdetected.}Safe"1fromn"circuitoftheoperatingmodeoutputsTheoperatingmodeselectorswitchonlyeverleadstooneoperatingmodeoutput"1"signal.ASmartkey®mustbeusedasthetransponderkey.Dependingontheapplicationareaanditsrespectiveregulations,theoperatingmodeselectorswitchcanbeuseduptoSILCL2(ENIEC62061)anduptoPLd(ENISO138491),iftheoperatingmodesareevaluatedbyasafetycontrolsystemwithsafe"1oon"evaluation.Switchingmustnotinitiateahazardousmovement,norcanitcancelanexistingcontrolcommand.
SafetyOperatingManualPITm2.1pDMG1003182EN02 113.2 Safetyregulations3.2.1 UseofqualifiedpersonnelTheproductsmayonlybeassembled,installed,programmed,commissioned,operated,maintainedanddecommissionedbycompetentpersons.Acompetentpersonissomeonewho,becauseoftheirtraining,experienceandcurrentprofessionalactivity,hasthespecialistknowledgerequiredtotest,assessandoperatetheworkequipment,devices,systems,plantandmachineryinaccordancewiththegeneralstandardsandguidelinesforsafetytechnology.Itisthecompany’sresponsibilityonlytoemploypersonnelwho:}Arefamiliarwiththebasicregulationsconcerninghealthandsafety/accidentprevention}Havereadandunderstoodtheinformationprovidedinthisdescriptionunder"Safety"}Andhaveagoodknowledgeofthegenericandspecialiststandardsapplicabletothespecificapplication.3.2.2 WarrantyandliabilityAllclaimstowarrantyandliabilitywillberenderedinvalidif}Theproductwasusedcontrarytothepurposeforwhichitisintended}Damagecanbeattributedtonothavingfollowedtheguidelinesinthemanual}Operatingpersonnelarenotsuitablyqualified}Anytypeofmodificationhasbeenmade(e.g.exchangingcomponentsonthePCBboards,solderingworketc.).3.2.3 Disposal}Whendecommissioning,pleasecomplywithlocalregulationsregardingthedisposalofelectronicdevices(e.g.ElectricalandElectronicEquipmentAct).
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 124 FunctiondescriptionTheoperatingmodeselectorswitchenablesyoutoswitchbetween5differentoperatingmodes(operatingmodesOM1...OM4andspecialoperatingmodeOM5(Service)).ForOM1...OM4,onebuttoneachisavailable.Forthespecialoperatingmode(Service),buttonOM1mustbeoperatedforacertainperiod(seeMonitoringofoperatingtime[ 45]).Eachbuttonisassignedamonitoredsemiconductoroutput.Operatingthebuttonchangesthesemiconductoroutputfroma"0"signaltoa"1"signal.Theoperatingmodeselectorswitchguaranteesthatonlyoneofthesemiconductoroutputshasa"1"signalatanyonetime.Transponder KeyRFIDReceiverPower A1A2SOM1SOM2IDo0IDo1IDo2IDo3SOM3SOM4SOM5User InterfaceSIo0SIo1SIo2SIo3IDi0IDi1InputsTerminalsKey ID Interface (Safe) Operating Modes InterfaceStatus InformationInterfaceFig.:BlockdiagramLegend:Transponderkey ElectronickeytoenableachangeofoperatingmodeUserinterface PushbuttontoselectanoperatingmodeA1,A2 Supplyvoltage
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 13SOM1…SOM5 OperatingmodeinterfaceInterfacefordisplayingtheselectedoperatingmode;consistsof5monitoredoutputsIDo0…IDo3andIDi0…IDi1KeyIDinterfaceInterfacefordownloadingtheKeyIDnumbertoacontrolsystem;consistsof4outputsand2inputsSIo0…SIo3 InterfaceforstatusinformationInterfaceforprovidingstatusinformation;consistsof4signaloutputsTheoperatingmodeselectorswitchisprotectedagainstunauthorisedoperation.Aswitchbetweenoperatingmodesmustbeenabledviaatransponderkey.TransponderkeyauthorisationsAtotalof6transponderkeysareavailableforanoperatingmodeselectorswitch.Eachtransponderkeyprovidesauthorisationtoswitchupto5operatingmodes,includingspecialauthorisations.Atransponderkeycanbeidentifiedviatheprintedkeymode.AssignmentofkeymodestoauthorisationsDesignationMarkingontransponderkey AuthorisationforoperatingmodeKeyMode01 OM1KeyMode02 OM1+OM2KeyMode03 OM1+OM2+OM3KeyMode04 OM1+OM2+OM3+OM4KeyService OM1+OM2+OM3+OM4+OM5(Service)+MasterauthorisationKeyMaster OM1+OM2+OM3+OM4+MasterauthorisationMasterauthorisation("KeyMaster")Withmasterauthorisation,theusercanbegrantedspecialauthorisationonthemachinecontrolsystemviatheKeyIDnumber.The"KeyMaster"transponderkeycanbeusedtoselectOM1...OM4.
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 144.1 InterfaceforstatusinformationVariousstatusinformationcanbesignalledviatheinterfaceforstatusinformation(seeBlockdiagram[ 12]).Thestatusinformationcanbeevaluatedthroughacontrolsystem.Thestatusinformationissubdividedintothefollowinginformationclasses:}Operatoractions– Inserttransponderkey– Removetransponderkey– Selectoperatingmode}Messages(e.g.usererror,fault)NOTICEWhentheoperatingmodeisselected(SIo3…SIo0=3h,8h...Bh)andwhenthereisadeviceerror(Dh)theinformationremainsindefinitelypresent.Allotherinformationstaysactiveforjust200ms.Afterthattimetheselectedoperatingmodeisagaindisplayed.Statusinformation InformationclassSIo3(MSB) SIo2 SIo1SIo0(LSB)Value(inHex)Reserved  0 0 0 0 0hReserved  0 0 0 1 1hTransponderkey5–Inserted[1] Operatoraction 0 0 1 0 2hOM5selected Operatoraction 0 0 1 1 3hTransponderkey1–Inserted[1] Operatoraction 0 1 0 0 4hTransponderkey2–Inserted[1] Operatoraction 0 1 0 1 5hTransponderkey3–Inserted[1] Operatoraction 0 1 1 0 6hTransponderkey4–Inserted[1] Operatoraction 0 1 1 1 7hOM1selected Operatoraction 1 0 0 0 8hOM2selected Operatoraction 1 0 0 1 9hOM3selected Operatoraction 1 0 1 0 AhOM4selected Operatoraction 1 0 1 1 BhNoauthorisation[2] Usererror 1 1 0 0 ChDeviceerror[3] Error 1 1 0 1 DhPushbuttonoperatedincorrectly[4] Usererror 1 1 1 0 EhTransponderkeyremoved Operatoraction 1 1 1 1 Fh
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 15[1]Whenapushbuttonisreleased,informationastowhichtransponderkeyisusedwillbedisplayedfor200ms(seeStatusinformation2hand4h…7h).Theselectedoperatingmodeisthendisplayed(seeStatusinformation3hand8h…Bh).PleaserefertotheTimingdiagramsforoperatoractions[ 16].[2]Thefault"Noauthorisation"(Ch)isregisteredinthefollowingcases:}Operatingmodeselectedwithouttransponderkey}Operatingmodeselectedwithatransponderkeythatisnotauthorisedfortheselectedoperatingmode}Transponderkeyisnotauthorisedfortheactiveoperatingmode}TransponderkeyisnotinsertedintimebeforetheoperatingmodeisselectedPleaserefertotheTimingdiagramsforusererror:"Noauthorisation"[ 18].[3]"Deviceerror"(Dh)issignalledintheeventofaninternaldeviceerrororwhenoneoftheoperatingmodeoutputsSOM1...SOM5arestuckbecauseofexternalvoltage(stuckat1orstuckat0).Remedy:}Rectifyerror,switchsupplyvoltageoffandthenonagain}ChangetheunitPleaserefertotheTimingdiagramfordeviceerror[ 17].[4]Thefault"Pushbuttonoperatedincorrectly"(Eh)isdisplayedinthefollowingcases:}Multipleoperationofpushbuttons}Pushbuttonoperatedfortoolong(timeoutforOM1toOM4=5sandtimeoutforOM5=10s)Note:Ifakeyisoperatedfor<50msthiswillnotbeevaluated,sotherewillbenoreaction.}PushbuttonwasreleasedafterthetransponderkeywasremovedPleaserefertotheTimingdiagramsforusererror:"Buttonoperatedincorrectly"[ 20].
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 164.1.1 TimingdiagramsforoperatoractionsThefollowingtimingdiagramsshowhowstatusinformationisregisteredatoutputsSlo0...Slo3,basedonoperatoractions.Legend:MessageisdisplayedconstantlyMessageisdisplayedbriefly(200ms)Selectoperatingmode1. Startposition:OM1isselected2. Operatoraction:Inserttransponderkey(e.g.AuthorisationKeyMode02)3. Operatoraction:Selectoperatingmode(e.g.Presspushbutton"2"forOM2)4. Operatoraction:RemovetransponderkeyFig.:Timingdiagramfor"Selectoperatingmode"
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 17Removetransponderkey1. Startposition:– OM5isselectedandthetransponderkey"KeyService"isinsertedor– OneoftheoperatingmodesOM1…OM4isselectedandatransponderkeywiththerelevantauthorisationisinserted2. Operatoraction:RemovetransponderkeyFig.:Timingdiagramfor"Removetransponderkey"4.1.2 TimingdiagramfordeviceerrorThefollowingtimingdiagramshowshowstatusinformationisregisteredatoutputsSlo0...Slo3,basedonadeviceerror.Legend:MessageisdisplayedconstantlyMessageisdisplayedbriefly(200ms)DeviceerrorFig.:Timingdiagramintheeventofadeviceerror
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 184.1.3 Timingdiagramsforusererror:"Noauthorisation"ThefollowingtimingdiagramshowshowstatusinformationisregisteredatoutputsSlo0...Slo3,basedontheusererror"Noauthorisation".Legend:MessageisdisplayedconstantlyMessageisdisplayedbriefly(200ms)OperatingmodeselectedwithouttransponderkeyFig.:Timingdiagramfor"Operatingmodeselectedwithouttransponderkey"OperatingmodeselectedwithatransponderkeythatisnotauthorisedfortheselectedoperatingmodeFig.:Timingdiagramforoperatingmodeselectionwherethereisinsufficientauthorisationfortheoperatingmoderequiringselection
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 19OperatingmodeselectedwithatransponderkeythatisnotauthorisedfortheactiveoperatingmodeSIo3:0Key Mode 01Pushbutton9hOM2 selectedCh 9hOM2 selectedNo authorisation4hTransponder Key 1 insertedttFig.:TimingdiagramforoperatingmodeselectionwherethereisinsufficientauthorisationfortheactiveoperatingmodeTransponderkeyisnotinsertedintimebeforetheoperatingmodeisselectedSIo3:0Key Mode 02Pushbutton „2"8hOM1 selectedCh 8hOM1 selected5hTransponder Key 2 insertedNo authorisation8hOM1 selectedttFig.:Timingdiagramforselectingtheoperatingmodebeforethetransponderkeyisinserted
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 204.1.4 Timingdiagramsforusererror:"Buttonoperatedincorrectly"ThefollowingtimingdiagramshowshowstatusinformationisregisteredatoutputsSlo0...Slo3,basedontheusererror"Buttonoperatedincorrectly"Legend:MessageisdisplayedconstantlyMessageisdisplayedbriefly(200ms)MultipleoperationofpushbuttonsFig.:Timingdiagramfor"Multipleoperationofbuttons"
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 21Buttonoperatedfortoolong}"Buttonoperatedfortoolong"withauthorisations"KeyMode01"…"KeyMode04"or}"Buttonoperatedfortoolong"withauthorisation"KeyService"SIo3:0 8hOM1 selectedEh 8hOM1 selectedPushbuttons „1" … „4"Key Mode 045 sPushbutton misusePushbutton „1"Key Service10 s8h Eh 8hOM1 selectedOM1 selectedPushbutton misusettSIo3:0ttFig.:Timingdiagramfor"Buttonoperatedfortoolong"PushbuttonwasreleasedafterthetransponderkeywasremovedSIo3:0Pushbutton „2"8hOM1 selectedFh 8hOM1 selectedKey ServiceTransponder Key removedttEhPushbutton misuseFig.:Timingdiagramforusererrorswhenreleasingthebutton
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 224.2 OperatingmodeinterfaceTheoperatingmodeinterfaceconsistsofthemonitoredoutputsSOM1…SOM5(seeBlockdiagram[ 12])."SOM"standsfor"SafeOperatingMode".Theoutputsareassignedtobuttons,whichcanbeusedtoselectanoperatingmodeiftheyhavetherelevantauthorisation(transponderkey):Pushbutton Output Operatingmode1 SOM1 OM1 TheoperatingmodeOM1/OM5isselectedbasedontheoperatingtimeofbutton1(seeMonitoringofoperatingtime[ 45])SOM5 OM52 SOM2 OM23 SOM3 OM34 SOM4 OM44.2.1 SwitchbehaviourafteratransponderkeyisremovedThechangeofoperatingmodeiscompletedbyremovingthetransponderkey.Oncethetransponderkeyhasbeenremoved,theoperatingmodeselectorswitchbehavesasfollows:Selectedoperatingmode AssignedoutputBehaviourafterthetransponderkeyisremovedOM1 SOM1 }Thepreviouslyselectedoperatingmodeismaintained.}Theassignedpushbuttonisbacklit.}Theassignedoutputhasa"1"signal.OM2 SOM2OM3 SOM3OM4 SOM4OM5 SOM5 }SwitchtoOM1}Pushbutton1isbacklit}SOM1hasa"1"signal
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 234.2.2 ControlprogramrequirementsInordertoachieveSILCL2(ENIEC62061)/PLd(ENISO138491)inanapplication,theevaluationmustbecarriedoutbyasafetyrelatedfunctionblock.Thesafetyrelatedfunctionblockmustmeetthefollowingrequirements:}Thefunctionblockmustenablesafe"1oon"evaluationoftheoutputsignalsatSOM1...SOM5.}Iftwoormoreoperatingmodesarepresentatthesametime,thismustbedetectedasanerror.INFORMATIONThefunctionblockmustbridgethet1switchoverdelay(seeSwitchoverdelayt1[ 45]).IfaPNOZmulti(e.g.PNOZm1p)isusedasthesafetycontrolsysteminconjunctionwithan"operatingmodeselectorswitch"functionelement,thenthisrequirementismetautomatically.
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 244.3 KeyIDinterfaceTheKeyIDinterface(seeBlockdiagram[ 12])isusedtodownloadtheKeyIDnumbertoacontrolsystem.4.3.1 KeyIDnumberofthetransponderkeyTheKeyIDnumberisusedtoclearlyidentifythetransponderkeyandisunique.Itisprintedonthetransponderkey’stypelabelasa9digitdecimalfigure.NOTICEPleasenote:TheKeyIDnumberisnotprintedonthetransponderkeypackaging.Ifthetransponderkeyislost,itisimpossibletosupplyareplacementtransponderkeywithanidenticalKeyIDnumber.TheKeyIDnumberconsistsoftwoparts:}Bit27=24:KeyMode(0…15D)}Bit23=00:Consecutivenumber(0…999999999D)Bit27 ... Bit24 Bit23 ... Bit16 Bit07 ... Bit00Consecutive NumberKey Mode Bit27 Bit26 Bit25 Bit2401 0 0 0 1 1D02 0 0 1 0 2D03 0 0 1 1 3D04 0 1 0 0 4DService 1 1 0 1 13DMaster 1 1 0 0 12DBit15 ... Bit080 ... 15D0 ... 999999999DFig.:StructureoftheKeyIDnumber
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 25Examples:1101 0000 0000 0010 1100Consecutive number: 44D0000 0000Key Mode ServiceKey-ID-Number: 1300000440010 0000 0000 1111 1110Consecutive number: 510D0000 0001Key Mode 02Key-ID-Number: 020000510
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 264.3.2 CommunicationmodefordownloadingtheKeyIDnumberTheuniqueKeyIDnumberfortherelevanttransponderkeyisdownloadedtothehigherlevelprocesscontrolsystemusingadefinedprotocol,dependingontheconfiguredcommunicationmode.ThecommunicationmodeisconfiguredontheKeyIDinterfaceoftheoperatingmodeselectorswitch(jumpersavailable/notavailable).Theoperatingmodeselectorswitchdetectstheconfiguredcommunicationmodeateachpoweron.Aslongasvoltageisappliedtotheoperatingmodeselectorswitch,theconfiguredcommunicationmodewillbeactive;thechangeincommunicationmodedoesnotcomeintoeffectuntilthesupplyvoltageisswitchedoffandthenonagain.It’spossibletochoosebetweenthefollowingcommunicationmodes:}Transmittercontrolledcommunicationmode}Handshakecontrolledcommunicationmode4.3.2.1 TransmittercontrolledcommunicationmodeWithtransmittercontrolledcommunicationmode,thedownloadoftheKeyIDnumberisstartedbytheoperatingmodeselectorswitch(=transmitter).Featuresofthiscommunicationmode:}DownloadofKeyIDnumberstartsoncethetransponderkeyisconnected}Constantbitrate(100ms)}Downloadon2datalines}Constantdownloadtime(typ.1.8s)}Monitoreddatadownload}Input/outputsrequiredonthecontrolsystem:4inputsand2outputs}Downloadisrepeatedbyreconnectingthetransponderkeyorifthetransponderkeyisinserted,viathecontrolsystembysendinga"1"signaltoIDi0foratleast50ms.NospecialcodingisrequiredontheKeyIDinterfaceinordertodownloadtheKeyIDnumberofatransponderkeytothecontrolsystemintransmittercontrolledcommunicationmode.TheterminalsontheKeyIDinterfaceareusedasfollows:KeyIDinterfaceBriefdescriptionofapplication CodingviajumpersIDo0 IDsync NoconfigurationrequiredIDo1 IDclockIDo2 IDout0IDo3 IDout1IDi0 IDin0IDi1 IDin1
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 274.3.2.2 HandshakecontrolledcommunicationmodeWithhandshakecontrolledcommunicationmode,thedownloadoftheKeyIDnumberisstartedbythecontrolsystem(Request).Featuresofthiscommunicationmode:}Downloadstartsviaarequesttothecontrolsystem,oncethetransponderkeyisconnected}Downloadisrepeatedbyarenewedrequesttothecontrolsystem}Variablebitrate(min.2PLCcyclesperbit)}Downloadon1dataline}Min.downloadtime:28Bit*(20ms+2*PLCcycle)}IdentifierforIDendforfeasibilitycheck}Input/outputsrequiredonthecontrolsystem:3inputsand1outputTheKeyIDinterfacemustbecodedwithajumperbetweenIDo3andIDi1inordertodownloadtheKeyIDnumberofatransponderkeytothecontrolsysteminhandshakecontrolledcommunicationmode.TheterminalsontheKeyIDinterfaceareusedasfollows:KeyIDinterfaceBriefdescriptionofapplication CodingviajumpersIDo0 IDsyncIDi1 Coding: INIDo3 Coding: OUTIDo1 IDresponseIDo2 IDdataIDo3 Coding:OUTIDi0 IDrequestIDi1 Coding:INInhandshakecontrolledcommunicationmode,theoperatingmodeselectorswitchcanbeoperatedinafunctionalvariant.InthiscasetheKeyIDnumberofthetransponderkeyisnotdownloadedtothecontrolsystem.ThecontrolsystemisonlyusedtoevaluateIDo0ontheKeyIDinterface.InthiscaseIDo0isusedasasignaloutput,enablingthecontrolsystemtorecognisewhetherthetransponderkeyisvalid/invalid.Withthisfunctionalvariant,only1inputisrequiredonthecontrolsystem.TheunusedterminalsontheKeyIDinterface(IDo1,IDo2andIDi0)mayremainunwired("open").
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 284.3.3 Evaluationbyacontrolsystem4.3.3.1 EvaluationoftheKeyIDnumberwithtransmittercontrolledcommunicationIDo0(IDsync)Bit 27 Bit 25 … Bit 16 Bit 15Bit 14IDo2(IDout0) Bit 26[c][d]tenIDo1(IDclock)[b]max. 100 msBit 13 Bit 11 … Bit 02 Bit 11Bit 00IDo3(IDout1) Bit 12Bit 27Bit 25 … Bit 16 Bit 15 Bit 14IDi0(IDin0) Bit 26Bit 13Bit 11 … Bit 02 Bit 11Bit 00IDi1(IDin1) Bit 12T[a]min. 60 ms [f][e]Fig.:TimingdiagramfortransmittercontrolledsignaldownloadLegend:Theadditionalterminaldesignations(IDsync,IDclock,IDout0etc.)areabbreviationsfortheterminalsignal'sapplication.IDo0 ControllineThesignalisgeneratedbytheoperatingmodeselectorswitch."0"signal Notransponderkeyisconnectedorthetransponderkeythatisconnectedisinvalid."1"signal Avalidtransponderkeyiscreated.Theoperatingmodeselectorswitchsignalstothecontrolsystemwhenthedownloadstarts.Thesignalispresentfor100ms.IDo1 TestpulselineThesignalisgeneratedbytheoperatingmodeselectorswitchandindicatesthevalidityofthedatabitsatIDo2andIDo3.}T=100ms}Dutycycle=50%IDo2,IDo3 DatalinesfortransmittingtheKeyIDnumberTheoperatingmodeselectorswitchsendstheKeyIDnumbertothecontrolsystemviathesetwodatalines.IDo2: SendBit27…Bit14IDo3 SendBit13…Bit00IDi0,IDi1 DatalineforreadingbacktheKeyIDnumberThecontrolsystemsendsthepreviouslyreceivedKeyIDnumberbacktotheoperatingmodeselectorswitchviathesetwodatalines.IDi0: ReceiveBit27…Bit14IDi1 ReceiveBit13…Bit00
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 29Downloadprocedure[a] TheoperatingmodeselectorswitchsetsthesignalatIDo0(IDsync:controlline)to"1"for100ms,therebysignallingtothecontrolsystemthattransmissionhasstarted.[b] ArisingedgeatIDo1(IDclock:testpulseline)indicatesthatthedataatdatalinesIDo2andIDo3ispresentandvalidandcanbereadbythecontrolsystem.[c] BythetimethereisafallingedgeatIDo1(IDclock:testpulseline),thecontrolsystemmusthavesentthepreviouslyreadbitbacktotheoperatingmodeselectorswitchviathedatalinesIDi0andIDi1.[d] BeforetherisingedgeatIDo1(IDclock:testpulseline),theoperatingmodeselectorswitchreadsthebitssentbacktoIDi0andIDi1bythecontrolsystemandchecksitforequivalence.[e] Atleast60msafterthefallingedgeatIDo1(IDclock:testpulseline),thelastbitsentbackbythecontrolsystemmustbepresentatdatalinesIDi0andIDi1.[f] Amaximumof100msafterthefallingedgeatIDo1(IDclock:testpulseline),thelastbitsentbackbythecontrolsystemmustbepresentatdatalinesIDi0andIDi1;inotherwords,bythispointatthelatest,datatransfermustbecompletedandthedatalinesmusthavea"0"signal.INFORMATIONIfthecontrolsystemdoesnotfeedbackthepreviouslyreadBitscorrectly,thedownloadisabortedandrestarted.The"IDsync"signalissetonceagain.ThedownloadisrepeateduntiltheKeyIDnumberisdownloadedcompletely.ThedownloadoftheKeyIDnumbertypicallytakes1.8s.
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 30FlowchartforevaluatingtheKeyIDinterface<IDsync> = 1Start<IDsync> = 0 No<IDclock> = 1Read <IDout0> AND <IDout1>Increment Bit CounterSet <IDin0> = <IDout0> Set <IDin1> = <IDout1> <IDclock> = 0 NoBit Counter = 14EndNoClear Bit CounterLast Bit Timer >= 60msStart Last Bit TimerNo[b][c][d][e][a]See Fig. „Timing Diagramm of sender controlled signal transfer“<IDsync> = 1Store ID-NumberClear<IDin0> AND <IDin1> [f]NoNoYesFig.:EvaluationoftheKeyIDnumberviaacontrolsystem(principle)
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 314.3.3.2 EvaluationoftheKeyIDnumberwithhandshakecontrolledcommunicationIDo0(IDsync)Bit 27Bit 25 … Bit 02 Bit 01Bit 00IDo2(IDdata)Bit 26tV[b][c][d][f]thtenIDo1(IDresponse)IDi0(IDrequest)[e][a]tatIDend200 ms [g]Fig.:TimingdiagramforhandshakecontrolledsignaldownloadLegend:Theadditionalterminaldesignations(IDsync,IDresponse,IDdataandIDrequestetc.)areabbreviationsfortheterminalsignal'sapplication.IDo0 ControllineThesignalisgeneratedbytheoperatingmodeselectorswitch."0"signal Notransponderkeyisconnectedorthetransponderkeythatisconnectedisinvalid.ThecontrolsystemcannotrequesttheKeyIDnumber."1"signal AvalidtransponderkeyisconnectedandthecontrolsystemcanrequesttheKeyIDnumber.IDo1 Handshakeline(Response)ThesignalisgeneratedbytheoperatingmodeselectorswitchandindicateswhetheradatabitatIDo2isvalid/invalid."0"signal ThedatabitatIDo2isinvalidandmaynotbeevaluated."1"signal ThedatabitatIDo2isvalidandmaybeevaluated.IDo2 DatalinefordownloadingtheKeyIDnumberTheKeyIDnumber(28Bit)isgeneratedbytheoperatingmodeselectorswitch.ThedownloadbeginswithMSB(Bit27…Bit00).IDi0 Handshakeline(Request)Thesignalisgeneratedbythecontrolsystem."0"signal NobitisrequestedatIDo2"1"signal AnewbitisrequestedatIDo2.ten IDsyncEnableTime(min.0ms)tvDataOutputValidTime(max.10ms)thDataOutputHoldTime(min.0ms)taDataOutputAccessTime(max.10ms)
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 32tIDend EndofKeyIDNumberTransfer(200ms)AfterthelastfallingedgeatIDi0,theoperatingmodeselectorswitchstillhasa"1"signalatoutputIDo1for200ms.Inthisway,theendoftheKeyIDnumberandthereforetheendofthedownload(EndofKeyIDNumberTransfer)isdisplayed.Thiscanbeusedforthefeasibilitycheck.Downloadprocedure[a] "1"signalatIDo0(controlline):Avalidtransponderkeyispresentattheoperatingmodeselectorswitch.[b] "1"signalatIDi0(handshakeline):ThecontrolsystemrequestsadatabitatdatalineIDo2an(=Request).[c] "1"signalatIDo1(handshakeline):TheoperatingmodeselectorswitchconfirmsthevalidityofthedatabitatdatalineIDo2(=Response).[d] "0"signalatIDi0(handshakeline):Thecontrolsystemconfirmsthatithasreadtherequesteddatabitwithouterror.[e] "0"signalatIDo1(handshakeline):TheoperatingmodeselectorswitchisreadytoissueanewdatabitatdatalineIDo2.[f] "0"signalatIDo0(controlline):Thetransponderkeyhasbeenremoved.[g] ThecontrolsystemmustrequestallthedatabitsofaKeyIDnumber(Bit27…Bit00).OnlythenisitpossibletostartdownloadinganewKeyIDnumber.Theendofthedownloadisindicatedbythesignalextension(tIDend)atIDo1.
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 33StatusdiagramforhandshakecontrolledsignaldownloadFig.:Statusdiagramforhandshakecontrolledsignaldownload
FunctiondescriptionOperatingManualPITm2.1pDMG1003182EN02 34FlowchartforevaluatingtheKeyIDinterface<IDsync> = 1AND<IDresponse> = 0Increment Bit CounterSet <IDrequest> = 0Read Bit <IDdata>Start TimerSet <IDrequest>= 1Set Bit Counter = 0Store ID Number<IDresponse> = 1No<IDresponse> = 0Time Control<tIDend> >= 200msNoBit Counter = 28Start[a][b][c][d][e]Last Bit ControlData Read and AcknowledgeBit RequestRequirementSee Fig. „Timing diagram of handshake controlled signal transfer“:See Fig. „State diagram of handshake controlled signal transfer“:<IDsync> = 0[g]NoYesNoNo[f]Fig.:EvaluationoftheKeyIDnumberviaacontrolsystem(principle)
InstallationOperatingManualPITm2.1pDMG1003182EN02 355 Installation5.1 GeneralinstallationguidelinesNOTICEPleasenotethattheoperatingmodeselectorswitchmayonlybeinstalledinacustomfitconsolewithaprotectiontypeofatleastIP54!}TheinstallationsitemustconformtotheprotectiontypeIP54.}Ensurethattheoperatingmodeselectorswitchhassufficientventilation.}Attachtheoperatingmodeselectorswitchusingthebracketsprovided.}Makesurethatthegasketisseatedcorrectly.
InstallationOperatingManualPITm2.1pDMG1003182EN02 365.2 DimensionsFrontview112122Sideview82203337
WiringOperatingManualPITm2.1pDMG1003182EN02 376 Wiring6.1 TerminalconfigurationINFORMATIONTheconnectionterminalsarenotsuppliedwiththeunit.X11 1 5 1 12Antenna + 1Antenna - 2n.c. 3SOM1 1SOM2 2SOM3 33SOM4 4SOM5 5IDo0 1IDo1 2IDo2 3IDo3 4IDi0 5IDi1 6SIo0 7SIo1 8SIo2 9SIo3 10A1 11A2 12X2 X3+ 24 V DC0 VFig.:TerminalconfigurationLegendAntenna+,AntennaTerminalsforconnectingtheantennan.c. NotconnectedSOM1..SOM5 Operatingmodeinterface:MonitoredsemiconductoroutputsforoperatingmodesOM1…OM5IDo0…IDo3 KeyIDinterface:SemiconductoroutputsforsendingtheoutputsignalstothecontrolsystemThefunctionoftheterminalsdependsonthecommunicationmodethathasbeenconfigured.IDi0…IDi1 KeyIDinterface:InputstoreceivetheinputsignalsfromthecontrolsystemThefunctionoftheterminalsdependsonthecommunicationmodethathasbeenconfigured.SIo0…SIo3 InterfaceforstatusinformationEvaluationofstatusinformationA1,A2 Terminalsforconnectingthesupplyvoltage
WiringOperatingManualPITm2.1pDMG1003182EN02 386.2 ConnectingtheunitProceedasfollows:1. ConnectingthesupplyvoltageaConnectthesupplyvoltageto(A1,A2).Pleasenotethefollowing:Thepowersupplymustmeettheregulationsforextralowvoltageswithprotectiveseparation(SELV,PELV).Thecablesfortheunit'ssupplyvoltage(A1,A2)mustbefittedwitha4Afuse,characteristicB/C.2. Connectingtheoperatingmodeinterface'ssemiconductoroutputsaConnecttheoperatingmodeinterface'ssemiconductoroutputstoacontrolsystemthatsupports"1ooN"evaluation.Youmustreadtheinformationconcerningintendeduse(seeIntendeduse[ 10]).3. Connectingtheinterface'sterminalsforstatusinformationaConnecttheterminals(SIo0...SIo3)toacontrolsystemthatsupportsevaluationofthestatusinformation.4. ConfigurecommunicationmodefordownloadingtheKeyIDnumberaTodownloadtheKeyIDnumberinhandshakecontrolledcommunicationmode,connectterminalsIDo3andIDi1oftheKeyIDinterface.Noconfigurationisrequiredfortransmittercontrolledcommunicationmode.5. ConnectingtheterminalsoftheKeyIDinterfaceaDependingontheselectedcommunicationmode,connecttheterminalsoftheKeyIDinterfacetoacontrolsystemthatsupportsthedownloadoftheKeyIDnumber.oraConnectIDo0toacontrolsystem,ifallyouwishtodoinhandshakecontrolledcommunicationmodeisevaluatewhetherthetransponderkeyisvalid/invalid.InthiscaseyouwillonlyuseIDo0asasignaloutput.TheunusedterminalsontheKeyIDinterface(IDo1,IDo2andIDi0)mayremainunwired("open").
WiringOperatingManualPITm2.1pDMG1003182EN02 396.3 ConnectiontoacontrolsystemDependingontheapplicationareaanditsrespectiveregulations,theoperatingmodeselectorswitchcanbeuseduptoSILCL2(ENIEC62061)anduptoPLd(ENISO138491),iftheoperatingmodesareevaluatedbyasafetycontrolsystemwithsafe"1oon"evaluation.Theexamplesbelowmeetthefollowingconditions:}APNOZm1pisusedasasafetycontrolsystem.}An"operatingmodeselectorswitch"functionelementisconfiguredinthePNOZmultiConfiguratorforsafe"1oon"evaluation.}TheKeyIDinterfaceandtheinterfaceforstatusinformationareevaluatedviaahigherlevelprocesscontrolsystem.}Thecablesfortheunit'ssupplyvoltage(A1,A2)containa4Afuse,characteristicB/C.
WiringOperatingManualPITm2.1pDMG1003182EN02 40Connectiontoacontrolsystem:TransmittercontrolledcommunicationmodePIT m2.1p Process Control SystemX3PNOZ m1pA1.A1A1.A1A1.A2A1.A2X7GND+24VX5A1.I5A1.I4A1.I3A1.I1InputSI03SIo2SIo1SIo0IDi1IDi0IDo3IDo2IDo1IDo0X31L+A1.I02345678910PEInputInputOutputInputInputInputInputPNOZmulti ConfiguratorFunction Element: Operating Mode Selector SwitchL-Power Supply24 V DCA111A212X2SOM11SOM22SOM33SOM44SOM55Key ID InterfaceInputOutput(Safe) Operating Modes InterfaceStatus Information InterfaceFDMG Fig.:Connectionfortransmittercontrolledcommunicationmode(example)
WiringOperatingManualPITm2.1pDMG1003182EN02 41Connectiontoacontrolsystem:HandshakecontrolledcommunicationmodePIT m2.1p Process Control SystemX3PNOZ m1pA1.A1A1.A1A1.A2A1.A2X7GND+24VX5A1.I5A1.I4A1.I3A1.I1InputSIo3SIo2SIo1SIo0IDi1IDi0IDo3IDo2IDo1IDo0X31L+A1.I02345678910PEInputInputOutputInputInputInputInputPNOZmulti ConfiguratorFunction Element: Operating Mode Selector SwitchL-Power Supply24 V DC(Safe) Operating Modes InterfaceA111A212X2SOM11SOM22SOM33SOM44SOM55Key ID InterfaceStatus Information InterfaceFDMG Fig.:Connectionforhandshakecontrolledcommunicationmode(example)
OperationOperatingManualPITm2.1pDMG1003182EN02 427 OperationSwitchonbehaviourINFORMATIONAftertheoperatingmodeselectorswitchisswitchedon(PowerON)oraftervoltageisreturned(reset),operatingmodeOM1isselectedautomatically.Thisalsoappliesifnotransponderkeyisconnected,oratransponderkeyisdetectedbutisinvalid.BehaviourintheeventofanerrorinoperatingmodesOM1…OM4NOTICEIntheeventofanerror,theunitdoesnotchangeoperatingmode.Theactiveoperatingmode(OM1,OM2,OM3orOM4)isdisplayedviathebacklitbuttonandtheassignedsemiconductoroutputhasa1signal.BehaviourintheeventofanerrorinspecialoperatingmodeOM5(Service)NOTICEIntheeventofanerror,theunitdoesnotchangeoperatingmode.Faultyoperationisindicatedbythefactthatallbuttonsareeitheralllitorallout.Theassignedsemiconductoroutputhasa1signal.
OperationOperatingManualPITm2.1pDMG1003182EN02 437.1 SelectoperatingmodesOM1...OM4Prerequisites}Atransponderkeywiththerelevantauthorisationsmustbepresent.}Theoperatingmodeselectorswitchmustrecognisethetransponderkeyasvalid.}Thetransponderkeymustbepresentattheoperatingmodeselectorswitchforthewholetimethebuttonisoperated.}Severalbuttonsmaynotbeoperatedsimultaneouslywhenselectinganoperatingmode.Procedure1. EstablishtransponderkeyconnectionaInsertthetransponderkeyintotheslotNote:Thetransponderkeymustsupporttheoperatingmode(s)intowhichyouwishtoswitch.2. SelectoperatingmodeaSelecttheoperatingmodeyouwantbypressingtherelevantpushbutton.Pleasenotetherequiredoperatingtime(seeMonitoringofoperatingtime[ 45]).Theoperatingmodehasbeenselectedcorrectlyifthepushbuttonisbacklitafteritisreleased.3. CompleteoperatingmodeselectionaCompletetheoperatingmodeselectionbyremovingthetransponderkey.Onceyouhaveremovedthetransponderkey,thelastoperatingmodetobeselectedismaintained(seeSwitchbehaviourafteratransponderkeyisremoved[ 22]).INFORMATIONYoucanswitchatwillbetweentheindividualoperatingmodesOM1,OM2,OM3andOM4;i.e.itispossibletoswitchfromOM1toOM3orfromOM4toOM2,forexample.
OperationOperatingManualPITm2.1pDMG1003182EN02 447.2 SelectspecialmodeOM5(Service)Prerequisites}AtransponderkeymustbeavailablewithauthorisationforspecialoperatingmodeOM5(Service).}Theoperatingmodeselectorswitchmustrecognisethetransponderkeyasvalid.}Thetransponderkeymustbepresentattheoperatingmodeselectorswitchforthewholetimethebuttonisoperated.}Severalbuttonsmaynotbeoperatedsimultaneouslywhenselectinganoperatingmode.Procedure1. EstablishtransponderkeyconnectionaInsertthetransponderkey"KeyService"intotheslot.2. SelectspecialmodeOM5(Service)aPresspushbutton1(OM1).Pleasenotetherequiredoperatingtime(seeMonitoringofoperatingtime[ 45]).Theoperatingmodehasbeenselectedcorrectlyifall4pushbuttonsflashwhenpushbutton1isreleased.ThepushbuttonsflashforaslongasyouareinspecialmodeOM5(Service).3. CompleteoperatingmodeselectionaCompletetheoperatingmodeselectionbyremovingthetransponderkey.Onceyouhaveremovedthetransponderkey,theoperatingmodeselectorswitchchangestoOM1(seeSwitchbehaviourafteratransponderkeyisremoved[ 22]).INFORMATIONSpecialoperatingmodeOM5(Service)canbeselectedfromanyoftheoperatingmodesOM1...OM4.
OperationOperatingManualPITm2.1pDMG1003182EN02 457.3 MonitoringofoperatingtimeAchangeofoperatingmodesisonlydetectediftherelevantbuttonhasbeenoperatedforadefinedtimeperiod.Button'soperatingtimePushbutton Operatingmode Output Operatingtime1 OM1 SOM1 >50msand<5s2 OM2 SOM23 OM3 SOM34 OM4 SOM41 OM5(Service) SOM5 >5sand<10s7.4 Switchoverdelayt1Onceabuttonhasbeenreleased,theassignedoutputontheoperatingmodeinterfaceswitchestoa"1"signalaftertheswitchoverdelayt1haselapsed(seeTechnicaldetails[ 48]).Thisdefinedswitchoverdelayguaranteesthatonlyoneoperatingmodeatatimehasa"1"signalattheassignedoutput.SOM1SOM2SOM3SOM4SOM5t1 t1Fig.:Timebehaviourwhenswitchingoperatingmode
OperationOperatingManualPITm2.1pDMG1003182EN02 467.5 TroubleshootingIfanerroroccursontheoperatingmodeselectorswitch,thelastoperatingmodetobesetwillberetained.Error Possiblecause RemedyUnabletoswitchtheoperatingmodeMultipleoperationofbuttonsMakesurethatonlyonebuttonisoperatedOperatingtimetoolongortooshortMakesurethattheperiodofoperationisobserved.TransponderkeyisnotdetectedMakesurethatthetransponderkeyisconnectedtotheoperatingmodeselectorswitchorinsertedcorrectly.Novalidauthorisation Makesurethatyouuseatransponderkeythathastherequiredauthorisation
OperationOperatingManualPITm2.1pDMG1003182EN02 477.6 DiagnosticsTheoperatingmodeselectorswitchhasvariousoptionsfordisplayingstatusinformation:}Interfaceforstatusinformation(SIo0…SIo3)}Buttonbacklighting7.6.1 StatusinformationabouttheinterfaceforstatusinformationVariousstatusinformationcanbesignalledviatheinterfaceforstatusinformation(seeBlockdiagram[ 12]).Thestatusinformationcanbeevaluatedthroughacontrolsystem(seeInterfaceforstatusinformation[ 14]).7.6.2 StatusinformationaboutpushbuttonbacklightingPushbuttons1…4(seeControlelements)havepushbuttonbacklighting.Pushbuttonbacklightingisusedtoindicatewhichoperatingmodeisactive;inotherwords,whichoutput(SOM1...SOM5)hasa"1"signal.EvaluationofpushbuttonbacklightingLegend:LEDonLEDflashesLEDoffLEDpushbutton1LEDpushbutton2LEDpushbutton3LEDpushbutton4 Meaning}Nosupplyvoltage}OM5(Service)isactive}SOM1hasa"1"signal}OM1isactive}SOM1hasa"1"signal}OM2isactive}SOM2hasa"1"signal}OM3isactive}SOM3hasa"1"signal}OM4isactive}SOM4hasa"1"signal
TechnicaldetailsOperatingManualPITm2.1pDMG1003182EN02 488 TechnicaldetailsGeneralApprovals CE,FCC,IC,TÜV,cULusListedSensor'smodeofoperation TransponderTransponderinterfaceEnergysupplytotransponder passive(batteryfree)Operatingfrequency 125kHzElectricaldataSupplyvoltageVoltage 24,0VKind DCVoltagetolerance 15%/+10%Outputofexternalpowersupply(DC) 1,0WResidualrippleDC 20%Continuousduty 100%Statusindicator LEDInputsNumber 2Signallevelat"0" 3+5VDCSignallevelat"1" 1530VDCVoltageatinputs 24VDCInputcurrentrange 2,0mAGalvanicisolation NoSemiconductoroutputsOverallperformanceext.loading,semiconductor 3,5WNumberofpositiveswitchingsinglepolesemiconductoroutputs 13SwitchingcapabilityVoltage 24VCurrent 20,0mASignallevelat"1" UB0,5VDCResidualcurrentat"0" 0,4mAShortcircuitproof YesTimesSwitchondelayafterUBisapplied 1,0sSupplyinterruptionbeforedeenergisation 20msSwitchoverdelayt1 50msOperatingtimepushbutton1...4 50ms...5sOperatingtime,servicepushbutton 5s...10sEnvironmentaldataClimaticsuitability DINIEC6006823AmbienttemperatureTemperaturerange 055°C
TechnicaldetailsOperatingManualPITm2.1pDMG1003182EN02 49EnvironmentaldataStoragetemperatureTemperaturerange 2570°CClimaticsuitabilityInaccordancewiththestandard EN60068278Humidity 95%r.h.at40°CEMC EN6094751VibrationInaccordancewiththestandard EN6006826Frequency 10,055,0HzAmplitude 0,35mmAirgapcreepageInaccordancewiththestandard EN606641Overvoltagecategory IIPollutiondegree 2Ratedinsulationvoltage 60VRatedimpulsewithstandvoltage 0,80kVProtectiontypeMountingarea(e.g.controlcabinet) IP54Housing IP20Terminals IP20MechanicaldataOperatingdistancesTypicaloperatingdistanceSo 5,0mmMax.cablelength 1000mMaterialBottom ST+10µZnFront ABSFixingscrewstorquesettings 0,30NmConnectiontype Springloadedterminal,pluginConductorcrosssectionwithspringloadedterminals:Flexiblewith/withoutcrimpconnector 0,202,50mm²,2412AWGSpringloadedterminals:Terminalpointsperconnection 1Strippinglength 9mmDimensionsHeight 33,0mmWidth 117,0mmDepth 82,0mmWeight 210gWherestandardsareundated,the201002latesteditionsshallapply.
TechnicaldetailsOperatingManualPITm2.1pDMG1003182EN02 508.1 SafetycharacteristicdataOperatingmodeENISO138491:2008PLENISO138491:2008CategoryEN62061SILCLEN62061PFHD[1/h]IEC61511SILIEC61511PFDENISO138491:2008TM[year]–PLd Cat.3 SILCL2 1,10E08 SIL2 5,28E04 20Alltheunitsusedwithinasafetyfunctionmustbeconsideredwhencalculatingthesafetycharacteristicdata.INFORMATIONAsafetyfunction'sSIL/PLvaluesarenotidenticaltotheSIL/PLvaluesoftheunitsthatareusedandmaybedifferent.WerecommendthatyouusethePAScalsoftwaretooltocalculatethesafetyfunction'sSIL/PLvalues.
SupplementarydataOperatingManualPITm2.1pDMG1003182EN02 519 Supplementarydata9.1 RadioapprovalFCC/ICapprovalUSA/Canada FCC ID: VT8- IC: 7482A- FCC/IC-Requirements: This product complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standards. Operation is subject to the following two conditions: 1) this product may not cause harmful interference, and 2) this product must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this product not expressly approved by Pilz may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Le présent produit est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) le produit ne doit pas produire de brouillage, et (2) l'utilisateur de le produit doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. PITM2PITM2
OrderreferenceOperatingManualPITm2.1pDMG1003182EN02 5210 Orderreference10.1 ProductType Features Orderno.PITm2.1pDMG Operatingmodeselectorswitchwithantenna40220110.2 AccessoriesTerminalsType Features Orderno.Springloadedterminals 1set 402304AntennaType Features Orderno.PITm2.1pDMGantenna Antenna 402202TransponderkeyType Features Orderno.PITm2.1keymode1 TransponderKeyMode01 402051PITm2.1keymode2 TransponderKeyMode02 402052PITm2.1keymode3 TransponderKeyMode03 402053PITm2.1keymode4 TransponderKeyMode04 402054PITm2.1keyservice TransponderKeyService 402055PITm2.1keymaster TransponderKeyMaster 402056
The Best of German En gineeringPartner of:SupportTechnical support is available from Pilz round the clock. AmericasBrazil+55 11 97569-2804Canada+1 888-315-PILZ (315-7459)Mexico+52 55 5572 1300USA (toll-free)+1 877-PILZUSA (745-9872)AsiaChina+86 21 60880878-216 Japan+81 45 471-2281South Korea+82 31 450 0680Australia+61 3 95446300EuropeAustria+43 1 7986263-0Belgium, Luxembourg+32 9 3217575France+33 3 88104000Germany+49 711 3409-444Ireland+353 21 4804983Italy+39 0362 1826711Scandinavia+45 74436332Spain+34 938497433Switzerland+41 62 88979-30The Netherlands+31 347 320477Turkey+90 216 5775552United Kingdom+44 1536 462203You can reach our international hotline on: +49 711 3409-444 support@pilz.comCMSE ®, InduraNET p ®, PAS4000 ®, PAScal ®, PASconfig ®, Pilz ®, PIT ®, PLID ®, PMCprimo ®, PMCprotego ®, PMCtendo ®, PMD ®, PMI ®, PNOZ ®, Primo ®, PSEN ®, PSS ®, PVIS ®, SafetyBUS p ®, SafetyEYE ®, SafetyNET p ®, the spirit of safety ® are registered and protected trademarks of Pilz GmbH & Co. KG in some countries. We would point out that product features may vary from the details stated in this document, depending on the status at the time of publication and the scope of the equipment. We accept no responsibility for the validity, accuracy and entirety of the text and graphics presented in this information. Please contact our Technical Support if you have any questions.Pilz develops environmentally-friendly products using ecological materials and energy-saving technologies. products and environmentally-friendly solutions.Pilz GmbH & Co. KG Felix-Wankel-Straße 2 73760 Ostfildern, GermanyTel.: +49 711 3409-0 Fax: +49 711 3409-133 info@pilz.comwww.pilz.com100XXXX-DE-0X0-0-2-3-000, 2014-00 Printed in Germany© Pilz GmbH & Co. KG, 20141003182EN02,201411PrintedinGermany©PilzGmbH&Co.KG,2011Backcover

Navigation menu